Diamond Saw Blade Manufacturer
- NCcuttingtools has more than 20 years of production diamond circular saw blade manufacturers experience.
- We have extensive experience in quality control and cost management.
- Provide you with the most competitive products.
Featured Products
segment Saw Blade
- Combined with sharpness and durability, the Segmented saw blade is the most versatile saw blade. Debris can be better discharged through the grooves while avoiding the damage caused by the high heat generated by the continuous processing of the diamond blades and the substrate.
- Segmented saw blades can be used in both dry and wet cutting modes.
Turbo Saw Blade
- Turbo saw blade is a cost-effective saw blade. Its continuous machining mode greatly improves machining accuracy. The shape of the turbine helps the saw blade perform better both in durability and debris evacuation.
- Turbo saw blade is often used for the fine processing of materials such as stone, concrete, ceramics, etc. Depending on the material, a variety of formulations are available.
- Turbo saw blade is usually used in small size processing machines.
Music Slot Tile Saw Blade
- Continuous rim saw blade is the sharpest saw blade. During the process of using, water needs to be added to cool down to protect the saw blade.
- Continuous rim saw blade is good at processing tiles, ceramics and other materials to make the edge of the processing more complete and neat.
- The recommended formula has a high diamond concentration and a good sharpness. The small size of the saw blade is used for the fine cutting of stone boards and tiles.
At present, with the development of substrate technology, there is a mute blade which can reduce the vibration of the substrate, thus reducing the production of noise.
Polishing Pad
- Dry Polishing Pad is mostly applied in the rough grinding stage and it has fast grinding speed. Besides, it has excellent wearability and long service life.
- Wet Polishing Pad is mainly used for stone polishing and fine grinding. The material will have a better gloss after polishing and the polishing speed is Fast.
Diamond Wire Saw
- Wire saw is a kind of cutting tool that uses high-strength metals and diamond segments. In the process of using it, you can use less space to cut large concrete, stone and so on. Especially when you are faced with large and irregular stones and concrete structures, the wire saw can be used for efficient segmentation.
- You can even cut stones with the wire saw underwater. Besides, when using the wire saw to cut precious stones, a customized ultra-fine wire saw can better reduce the consumption of your stones.
Diamond Tools Classification By Use
Grinding Tools
- Abrasive Wheels
- Edge Grinding Wheels
- Grinding Wheels
- Idler Wheels
- Tumbling Barrels
Cutting Tools
- Circular Saw
- Gang Saw
- Wire Saw
- Band Saw
- Chain Saw
What We Can Do For You
Do you want to know more about how to customize your diamond saw blade? How to customize your logo? How to design your packaging? You can always contact us!
stay connected
How We
Can Help
Customized Service
Support extremely high customization requirements such as segment size, diamond density, colour and logo, substrate size, super large base saw blade, no MOQ, multi-device matching, all-round technical support and other services.
Diamond saw blade manufacturing Technique
Very welcome to visit our factory, contact our support team to confirm your visit.
Sintered saw blade production process
Welding saw blade production process
Our Equipment
important things you should know
Questions And Answers
A: Usually caused by dirty water, insufficient water supply to blade, low powered drive motor, worn bearings or shaft, incorrect blade for material being cut.
A: Check bearings and spindle for wear,machine alignment and equal water supply to both sides of blade.
A:Ⅰ.Incorrect mounting of blade/remount blade correctly.
Ⅱ.Worn bearings or bent shaft/replace worn bearing or blade shaft.
Ⅲ.Blade RPM too high or incorrect tension/ensure blade is running at correct RPM.
A:Ⅰ.Blade becoming glazed due to use on material too hard for bond/ To sharpen balde,make fast (3-4m/min) shallow (3-10mm deep) passed in the material being cut, or in sandstone or asphalt for quicker results.
Ⅱ.Excessive cutting pressure, high shaft RPM, low machine HP or drive belts loose/ tune engine according to manufacturer’s manual.
A:Ⅰ.Blade too hard for material being cut/use proper blade specification for material being cut.
Ⅱ.Overheating due to lack of water/check water feed system and make sure the water flow is adequate on both sides of the blades.
Ⅲ.Blade twisting or jamming in cut/keep sawing straight when the blade working(concave blade exceptional).
Ⅳ.Out of round blade/replace worn bearing, realign blade shaft or replace worn blade arbor.
Ⅴ.Incorrect blade tension/ensure blade is running at correct RPM.
Ⅵ.Excessive cutting speed/slow down the cutting speed.
Ⅶ.Undercutting of steel center/use sufficient water to flush out the cut or choose blade with protective teeth.
A:Ⅰ.Incorrect mounting of blade/remount blade correctly.
Ⅱ.Worn bearings, spindle or blade arbor/replace worn bearing, realign blade shaft or replace worn blade arbor.
Ⅲ.Blade too hard for material being cut/use proper blade specification for material being cut.
A: Abrasion of steel center due to highly abrasive material being cut/use sufficient water to flush out the chipping or choose blade with protective teeth.
A:Ⅰ.Excessive cutting pressures/slow down the cutting speed and keep correct feed rate.
Ⅱ.Incorrect blade tension/ensure blade is running at correct RPM.
Ⅲ.Jamming or twisting in cut/keep sawing straight when the blade working(concave blade exceptional).
Ⅳ.Overheating/check water feed system and make sure the water flow is adequate on both sides of blades.
Ⅴ.Blade too hard for material being cut/use proper blade specification for material being cut.
A: Blade too hard for material being cut/use proper blade specification for material being cut.
A:Ⅰ.Blade incorrectly seated/remount the blade correctly.
Ⅱ.Worn flanges or flanges not properly tightened/tighten flanges properly or replace worn flanges.
Ⅲ.Blade shaft worn/replace worn blade shaft.
A:Ⅰ.Incorrect mounting of blade/remount blade correctly.
Ⅱ.Worn bearings, spindle or blade arbor/replace worn bearing, realign blade shaft or replace worn blade arbor.
Ⅲ.Blade too hard for material being cut/use proper blade specification for material being cut.
A:Ⅰ.Blade too hard for material being cut/use proper blade specification for materila being cut.
Ⅱ.Overheating due to lack of water/check water feed system and make sure the water flow is adequate on both sides of blades.
Ⅲ.Blade twisting or jamming in cut/keep sawing straight when the blade working(concave blade exceptional).
Ⅳ.Out of round blade/replace worn bearing, realign blade shaft or replace worn blade arbor.
Ⅴ.Incorrect blade tension/ensure blade is running at correct RPM.
Ⅵ.Excessive cutting speed/slow down the cutting speed.
Ⅶ.Undercutting of steel center/use sufficient water to flush out the cut or choose blade with protective teeth.
What People Say About Us
Client Testimonials
“NCCutting Tools is a professional and responsible company.
Their saw blades are of high quality and the delivery is faster than I expected.
They also have strict regulations on quality control and cost management.
Really help me cut off a lot of costs and save time!
”
John DanielCEO 